100% Canadian

All prices are in CDN dollars.

1-800-585-9331

GPSC PN
Availability
Notify Me

Important Note

DO NOT directly connect an RSP to the same antenna as your transmitter, or to an antenna in the near field of a transmitting antenna, as this is likely to result in irreversible damage to your RSP and invalidate your warranty.

Product Specifications

General

  • Weight 315g
  • Size: 95mm x 80mm x 30mm
  • Low Current:
  • Single tuner:180 mA (excl Bias T)
  • Both tuners: 280 mA (excl Bias T)

Frequency Range

  • Continuous coverage 1kHz – 2GHz

Connectivity

  • USB 2.0 (high speed) type B socket

Tuner 1 Antenna Coax Port Characteristics

  • 1kHz – 2GHz operation
  • 50Ω input impedance
  • SMA female connector

Tuner 1 High-Z Port Characteristics

  • 1kHz – 30MHz operation
  • 1kΩ input impedance (balanced)
  • Pluggable screw connector
  • (CTB9208/3 plug supplied)

Tuner 2 Antenna Port Characteristics

  • 1kHz – 2GHz operation
  • 50Ω input impedance
  • SMA female connector
  • Selectable 4.7V DC out (see Bias T)

Reference Clock Input and Output

  • MCX female connector

ADC Characteristics

  • Sample frequency 2 – 10.66MSPS
  • 14 bit native ADC (2 – 6.048MSPS)
  • 12-bit (6.048- 8.064 MSPS)
  • 10-bit (8.064- 9.216MSPS)
  • 8-bit (> 9.216 MSPS )

Bias T (Tuner 2 Port only)

  • Software selectable 4.7V @ 100mA

Maximum recommended input power

  • 0dBm continuous, 10dBm for short periods

Typical Noise Figures (50 ohm)

  • 18dB @ 2MHz
  • 15dB @ 12MHz
  • 15dB @ 25MHz
  • 15dB @ 40MHz
  • 3.3dB @ 100MHz
  • 3.3dB @ 200MHz
  • 5.8dB @ 340MHz
  • 3.6dB @ 660MHz
  • 4.3dB @ 1500MHz
  • 5.0dB @ 1800MHz

Typical Noise Figures (High-Z)

  • 14dB @ 2MHz
  • 18dB @ 15MHz

IF Modes

  • Zero IF, All IF bandwidths
  • Low IF, IF bandwidths ≤ 1.536MHz

IF Bandwidths (3dB)

  • 200kHz
  • 300kHz
  • 600kHz
  • 1.536MHz
  • 5.0MHz
  • 6.0MHz
  • 7.0MHz
  • 8.0MHz

Maximum recommended input power

  • 0dBm continuous
  • 10dBm for short periods

Reference

  • High temp stability 0.5PPM TCXO
  • In-field trimmable to 0.01ppm.

External Reference Clock

  • When an external clock is applied, auto-detect will switch to the external reference. Ideally the external clock source should be connected to the RSPduo before power up

Front End Filtering (Coax Antenna Ports)

Automatically configured front end filtering:

Low Pass

  • 2MHz

Band Pass

  • 2-12MHz
  • 12-30MHz
  • 30-60MHz
  • 60-120MHz
  • 120-250MHz
  • 250-300MHz
  • 300-380MHz
  • 380-420MHz
  • 420-1000MHz

High Pass

  • 1000MHz

Notch Filters (Coax Antenna Ports)

  • FM Notch Filter:
    • 30dB 77 – 115MHz
    • 50dB 85 – 107MHz
    • 3dB 144 – 148MHz
  • MW Notch Filter:
    • 15dB 400 – 1650kHz
    • 30dB 500 – 1530kHz
    • 40dB 540 – 1490kHz
  • DAB Notch Filter:
    • 20dB 155 – 235MHz
    • 30dB 160 – 230MHz

Front End Filtering (High Z Tuner 1 Port)

  • Choice of 0-2MHz and 0-30MHz low pass

Notch Filters (High Z Tuner 1Port)

  • MW Notch Filter:
    • 15dB 490 – 1640kHz
    • 30dB 560 – 1470kHz
Note: The notch filters above are software selectable and remove specific broadcast bands. Each port carries its own filters which can be independently selected.

Operating Modes

  • One receive stream, any IF mode or bandwidth, software selectable from either tuner, or….
  • Two simultaneous receive streams from both tuners using low IF mode and bandwidth limited to 1.536MHz maximum
  • These modes are summarised in the table below.
Operating Mode
Tuner 1 Available RF ports
Tuner 2 Available RF ports
Master Sample Rate
Slave Sample Rate
Tuner 1 IF Bandwith
Tuner 2 IF Bandwith
Tuner 1 Frequency Range
Tuner 2 Frequency Range
Single Receiver (Tuner 1)
50Ω/Hi-Z
N/A
2-10 MHz
N/A
200kHz - 8 MHz
N/A
1kHz - 2 GHz
N/A
Single Receiver (Tuner 2)
N/A
50Ω with Bias T
2-10 MHz
N/A
N/A
200kHz - 8 MHz
N/A
1kHz - 2 GHz
Dual Tuner (Tuner 1 master)
50Ω/Hi-Z
50Ω with Bias T
6/8 MHz
Determined by Tuner 1
200kHz - 1536MHz
200kHz - 1536MHz
1kHz - 2 GHz
1kHz - 2 GHz
Dual Tuner (Tuner 2 master)
50Ω/Hi-Z
50Ω with Bias T
6/8 MHz
Determined by Tuner 2
200kHz - 1536MHz
200kHz - 1536MHz
1kHz - 2 GHz
1kHz - 2 GHz
DO NOT directly connect an RSP to the same antenna as your transmitter, or to an antenna in the near field of a transmitting antenna, as this is likely to result in irreversible damage to your RSP and invalidate your warranty.